EMP Multiswitch ProfiLine voor maximaal 4 satellieten
Topkwaliteit multiswitch in ProfiClass uitvoering. Ontvang 4 satellietposities met 4 quattro LNBs om diverse tuners aan te sluiten! Deze kunnen volledig onafhankelijk van elkaar werken. Switch wordt binnen aangesloten op eigen voeding.
Kies bij het bestellen eenvoudig het aantal uitgangen!
Deze ProfiLine versie is geschikt voor zowel Quattro alsook voor QUAD LNB's
verkrijgbare modellen van 4 tot en met 26 uitgangen.
4-satellites (16 polarities) standalone multiswitches with an integrated power supply are designed for the distribution of terrestrial and satellite signals from 4 satellite positions for up to 26 subscribers. Multiswitches are compatible with all satellite receivers, which support DiSEqC control system. They are suitable for both analog and digital reception. The multiswitches and integrated power supplies are designed for maximum efficiency in full operation, eliminating need for stand-by mode functionality.
Advantages of PROFI CLASS multiswitches
- input attenuators at all inputs
- configurable support for Quad LNBs
- selectable active / passive processing of terrestrial band
- 12V DC supply for terrestrial preamplifier
- extended temperature range
4 SATELLITES MULTI-SWITCHES | ||||
| Type | Inputs | Outputs | Description | |
| MS17/4PIU-6 V10 | 17 | 4 | DiSEqC multiswitch with integrated power supply, 0 to 15 dB attenuators, Quad LNB compatible, switchable active/passive terr. input | |
| MS17/8PIU-6 V10 | 17 | 8 | ||
| MS17/12PIU-6 V10 | 17 | 12 | ||
| MS17/16PIU-6 V10 | 17 | 16 | ||
| MS17/20PIU-6 V10 | 17 | 20 | ||
| MS17/26PIU-6 V10 | 17 | 26 | ||
Useful information
- Multiswitches are controlled by receiver using analog and DiSEqC 1.0 commands:
command sent by receiver selected input of multiswitch 13 V, 0 kHz, DiSEqC A (1) A 18 V, 0 kHz, DiSEqC A (1) B 13 V, 22 kHz, DiSEqC A (1) C 18 V, 22 kHz, DiSEqC A (1) D 13 V, 0 kHz, DiSEqC B (2) E 18 V, 0 kHz, DiSEqC B (2) F 13 V, 22 kHz, DiSEqC B (2) G 18 V, 22 kHz, DiSEqC B (2) H 13 V, 0 kHz, DiSEqC C (3) I 18 V, 0 kHz, DiSEqC C (3) J 13 V, 22 kHz, DiSEqC C (3) K 18 V, 22 kHz, DiSEqC C (3) L 13 V, 0 kHz, DiSEqC D (4) M 18 V, 0 kHz, DiSEqC D (4) N 13 V, 22 kHz, DiSEqC D (4) O 18 V, 22 kHz, DiSEqC D (4) P - Multiswitches are not compatible with Monoblock LNBs
- If higher than available number of user outputs is required, simply use two multiswitches instead of one, routing LNB outputs via signal splitters
- If terrestrial band is used, terminate all unused outputs by 75 ohm loads
- Switching between active and passive processing of terrestrial band is performed by lever No. 1 of configuration DIP-switch
- 22 kHz tone required for Quad LNB can be disabled by DIP-switch
- DC supply for preamplifier of terr. antenna is limited to 150 mA max. The supply is disconnected if higher load or short circuit is applied to terrestrial input. To keep power consumption at minimum level is however recommended to include external DC block if short-circuit conditions should persist on terrestrial input
Brief specification:
| Parameter | Condition | Value |
| Frequency range | Sat. inputs | 950-2300 MHz |
| Terr. input | 5-862 MHz (passive) 40-862 MHz (active) | |
| Outputs | 5-2300 MHz (passive) 40-2300 MHz (active) | |
| Control | DiSEqC 1.0 (2.0) commands | |
| Insertion loss | Sat. | 0 dB avg |
| Terr. passive | 16 dB avg | |
| Terr. active | 2 dB avg | |
| Sat. inputs isolation | Between V/H polarisations | 20 dB min |
| Between low/high bands | 20 dB min | |
| Between sat. systems | 25 dB min | |
| Maximum input level* | Sat. | 90 dBµV avg** |
| Terr. | 100 dBµV avg (passive) 90 dBµV avg (active) | |
| Maximum output level* | Sat. | 90 dBµV avg |
| Terr. | 84 dBµV avg (passive) 88 dBµV avg (active) | |
| Power consumption | From each receiver | 75 mA (18 V) |
| From internal power supply | 4.5 W (passive) + LNB 6.5 W (active) + LNB | |
| Terr. preamplifier supply | 150 mA max (12 V DC) | |
| Dimensions (w,d,h) | 47.0 x 15.2 x 8.7 cm (power cord length 130 cm) | |
| Temperature range | -30 ~ +70 °C |
